A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

FDI飞机舵面损伤故障全局检测的非线性数学模型

阐述了飞机在单舵面损伤故障下 ,建立故障状态下的数学模型 ,以及同样输入条件下飞机正常运动时的数学模型 ,得到飞机在相同飞行条件下损伤时的气动系数和无损伤正常时的气动系数 ,最终得到气动系数的残差。这将为以后飞机过载残差和角加速度残差奠定基础。论文中结合一定的算例给予证实推论的正确性。     

Calculation of the transonic dip of airfoils using viscous-inviscid aerodynamic interaction method

A numerical procedure for the calculation of the transonic dip of airfoils in the time domain is presented. A viscous-inviscid aerodynamic interaction method is taken to calculate the unsteady aerodynamic loads. In the present case the integral boundary layer equations are coupled with the Transonic Small Disturbance (TSD) Potential Equation. The coupling between structural motion and aerodynamic loads is carried out using State Space equation. It is solved by State Transition Matrix technique. Results are presented for NACA 64A010 and NLR 7301 airfoils with structural data from Isogai and DLR, respectively. Comparisons show good agreement with other numerical results. Certain deviations of experimental data taken from literature need more insight in the detailed test conditions.     

非线性四阶微分方程两点边值问题解的存在唯一性

讨论了非线性四阶微分方程y(4)=f(x,y,y',y',y')的两点边值问题解的存在唯一性。其中,函数f在[a,b]×R4上连续,且满足Lipschitz条件。     

褶皱结构成形时的形状偏差计算

解决了褶皱结构成形时相邻的平行四边形平面元素之间连接区棱的修圆半径值预测问题。把毛坯模拟成薄板，定义了平行四边形平面元素的边界条件，采用能量法导出挠度和力函数的非线性微分方程组，利用积分－差分法实现其数值解，并提供计算结果和分析应力－应变场。采用的计算方法可用于研究毛坯的刚度参数和工艺参数对褶皱结构的形状影响。     

备件配置方法研究

针对电路板件故障数据记录的实际,运用可靠性理论,提出了没有故障数据板件的备件数量计算方法;对有故障统计数据的板件引用了经验模型来确定备件配置。     

EFFECT OF THE RIBLETS SURFACE ON THE BOUNDARY LAYER DEVELOPMENT

ＥＦＦＥＣＴ　ＯＦ　ＴＨＥ　ＲＩＢＬＥＴＳ　ＳＵＲＦＡＣＥ　ＯＮ　ＴＨＥ　ＢＯＵＮＤＡＲＹ　ＬＡＹＥＲ　ＤＥＶＥＬＯＰＭＥＮＴＷａｎｇＪｉｎｊｕｎ；ＬａｎＳｈｉｌｏｎｇ；ＬｉａｎＱｉｘｉａｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＦｌｕｉｄＭｅｃｈａｎｉｃｓＩＢｅ...     

Modelling of Spall in an Anisotropic Aluminium Alloy

Spall caused by hypervelocity impacts at the lower range of velocities could result in significant damage to spacecraft. A number of polycrystalline alloys, used in spacecraft manufacturing, exhibit a pronounced anisotropy in their mechanical properties. The aluminium alloy AA 7010, whose orthotropy is a consequence of the meso-scale phase distribution or grain morphology, has been chosen for this investigation. The material failure observed in plate impact was simulated using a number of spall models. The Hugoniot elastic limit and spall strength have been studied as a function of orientation, and compared to experimental results.     

八丝热线探针制作及其应用

介绍了八丝热线探针的制作工艺,有效地消除了各热丝探头之间的电信号干扰和动力学干扰。实验中使用该探针检测到了湍流边界层内的大尺度旋涡,并测量了它们的强度和尺度。与此同时还获得了速度、湍流强度和功率谱等流场参数,结果与现有典型数据一致。说明本文所述的多丝热线探针具有很强的实用性。     

基于损伤力学的概率疲劳曲线获取方法

文章基于损伤力学方法获得满足疲劳试验的损伤演化方程,推导出一般条件下的理论疲劳曲线以及相对应的理论中值疲劳曲线与理论理想疲劳曲线；然后根据试验数据即可确定理论疲劳曲线中的参量,从而获取疲劳曲线计算公式。通过此计算公式,可以方便地得到一组以初始损伤为参数的疲劳曲线族,继而得到以失效概率为参数的疲劳曲线族,大大降低了所需试验的数量,并为结构抗疲劳设计和寿命估算提供了依据。